- What can I use instead of drywall on ceiling?
- Why do you drywall the ceiling first?
- Why do you double drywall?
- Does double drywall reduce sound?
- Do you stagger drywall on ceilings?
- Do you plaster ceiling or walls first?
- How thick should drywall be?
- Can you use 3/8 drywall ceiling?
- What is the weight of 3/8 drywall?
- What thickness of drywall should I use on the ceiling?
- When should you use 3/8 drywall?
- What is a Level 3 Drywall finish?
- How much does it cost to have someone mud and tape drywall?
- What is code for drywall on ceilings?
- Can you put two layers of drywall on ceiling?
- What size screws 3/8 drywall?
- Is it better to hang drywall vertical or horizontal?
- Do you hang drywall on ceiling first?
- Can you put new drywall over existing drywall?
What can I use instead of drywall on ceiling?
If you are planning on redoing your walls or ceilings, the typical materials you’ll use include Sheetrock or finished plywood.
Each has its benefits as a building material and in some cases, finished plywood is the better alternative..
Why do you drywall the ceiling first?
Doing the ceiling first means you can lift the wall sheets to make a tight joint. By contrast if you do the walls first you would have to sculpt every edge to make it seat tightly, and/or end up with lots of voids to fill before you tape. My crews going back 20 years have always done ceilings before walls.
Why do you double drywall?
Dual layers of drywall = increased mass. Increased mass = sound deadening. Putting green glue between the two layers of drywall acts as a decoupler, so that the outermost layer of drywall “floats” and doesn’t transfer the sound waves from your subwoofer through to the rest of the wall.
Does double drywall reduce sound?
Double Drywall benefits The benefit of a double thickness of drywall with Green Glue sandwiched between is less noise penetration. The drywall adds mass, which prevents sound wave penetration, especially lower frequency, and the Glue absorbs sound vibration-damping sound vibration movement.
Do you stagger drywall on ceilings?
It’s not necessary to stagger seams on ceiling drywall. However, because these joints are relatively difficult to finish—and tend to be noticeable in the finished product—it’s a good idea to stagger the drywall panels to make the joints less visible.
Do you plaster ceiling or walls first?
If you’re working on ceilings and walls, always start with the ceiling, starting in the left corner. Run your trowel back and forth, applying your plaster in a straight line. The coat needs to be roughly three to four millimetres thick.
How thick should drywall be?
1/2-inchMost drywall measures 1/2-inch thick. It’s the most common choice for interior walls because they are easy to carry and hang. If weight is a concern, consider ultra-light half-inch drywall. It’s 13 pounds lighter than other varieties for the same size and thickness.
Can you use 3/8 drywall ceiling?
Yes, you can use a 3/8″ drywall for a ceiling. To prevent sagging ensure ceiling frames supporting the drywall are 16″ apart.
What is the weight of 3/8 drywall?
Using lbs/ft2 calculations for 48” wide sheetsLbs/ft28 ft long1/4” Standard1.238.43/8” Standard1.444.81/2” Standard1.651.25/8” Standard2.270.42 more rows
What thickness of drywall should I use on the ceiling?
1/2-inch: Half-inch drywall panels are the standard thickness for interior walls, as well as ceilings. 5/8-inch: These panels are commonly used for ceilings, or for walls that require a prescribed fire-resistant rating.
When should you use 3/8 drywall?
Each thickness has its own benefits and applications it’s best suited for.1/4 inch. The most economical option. … 3/8 inch. This thickness is perfect for remodeling partitions. … 1/2 inch. This drywall thickness is available in a variety of panel lengths. … 5/8 inch.Aug 11, 2016
What is a Level 3 Drywall finish?
Level 3: All joints and interior angles shall have tape embedded in joint compound and shall be immediately wiped with a joint knife leaving a thin coating of joint compound over all joints and interior angles. One (1) separate coat of joint compound shall be applied over all joints and interior angles.
How much does it cost to have someone mud and tape drywall?
Cost to tape and mud drywall To finish the drywall, it costs $1 to $1.65 per square foot. This works out to between $30 and $60 per pre-manufactured panel that’s hung on the studs and finished with texture.
What is code for drywall on ceilings?
e. Type X gypsum board for garage ceilings beneath habitable rooms shall be installed perpendicular to the ceiling framing and shall be fastened at maximum 6 inches o.c. by minimum 17/8 inches 6d coated nails or equivalent drywall screws.
Can you put two layers of drywall on ceiling?
Ceiling drywall is 5/8 inch thick, and wall drywall is 1/2 inch thick. Install a second layer of drywall on top of the first layer to create a better sound barrier as well as better insulation.
What size screws 3/8 drywall?
Buy 1-1/4-in. coarse-thread drywall screws to attach 3/8-in., 1/2-in. and 5/8-in. drywall to wood framing.
Is it better to hang drywall vertical or horizontal?
On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. … For walls 9 feet high or shorter, hanging the drywall horizontally has a number of benefits. Fewer seams. Horizontal hanging reduces the lineal footage of seams by about 25%.
Do you hang drywall on ceiling first?
Hanging Drywall From the Top Down Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. … are of no concern, but seriously warped framing will require you to use drywall shims–long strips of 1/8- or 1/16-in.
Can you put new drywall over existing drywall?
Studs. Hanging new drywall over existing walls is very similar to hanging drywall in a new construction setting. … This process is relatively simple with walls that are paneled because you can actually see the original nail holes with the naked eye. Just follow the holes to the ceiling and make a mark.