- Is it better to hang drywall vertical or horizontal?
- How much gap should be between sheets of drywall?
- Should drywall be butted tight?
- Does drywall sit on subfloor?
- Why do you hang drywall on the ceiling before the walls?
- Should I drywall or floor first?
- How big of a hole can you fill with drywall mud?
- Can you use 1/2 inch drywall ceiling?
- What can I use instead of drywall on ceiling?
- How much drywall do I need for ceiling?
- Should I nail or screw drywall?
- Why do screws pop in drywall?
- How much weight can a screw in drywall hold?
- What is better sheetrock or drywall?
- Do you hang drywall top to bottom?
- Does drywall go on the ceiling?
- Should drywall touch the floor?
- How big of a gap can you fill with drywall mud?
- Can you put too many screws in drywall?
Is it better to hang drywall vertical or horizontal?
On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically.
For walls 9 feet high or shorter, hanging the drywall horizontally has a number of benefits.
Horizontal hanging reduces the lineal footage of seams by about 25%..
How much gap should be between sheets of drywall?
Unfortunately, there is no retroactive fix. However, during installation, be diligent about keeping that 1/8-inch space between sheets by using a guide. The blade of a drywall square is about 1/8-inch thick and does the trick. Thin strips of wood can also be used as spacing guides.
Should drywall be butted tight?
Hanging Drywall Vertically: Leave a 1/8-in. It’ll usually just cause trouble. Jamming in a piece that’s too tight will crumble the edge or break out a corner (left). And removing a piece to shave a too-tight edge is messy and time consuming. A loose fit avoids this problem.
Does drywall sit on subfloor?
In standard home construction, the contractor installs the subfloor before installing the drywall. In fact, the subfloor is one of the first features of construction, whereas drywall installation takes place toward the end of the project.
Why do you hang drywall on the ceiling before the walls?
Doing the ceiling first means you can lift the wall sheets to make a tight joint. By contrast if you do the walls first you would have to sculpt every edge to make it seat tightly, and/or end up with lots of voids to fill before you tape. My crews going back 20 years have always done ceilings before walls.
Should I drywall or floor first?
When you’re hanging drywall and installing new flooring, it’s usually best to hang the drywall first and then save the floor for last.
How big of a hole can you fill with drywall mud?
Use spackle to repair holes less than 4 inches (10 cm) in diameter. Spackle can be used to repair holes up to the size of your hand. You will have to use a support like mesh or wire to repair holes larger than 4 inches (10 cm) in diameter. Buy light spackle at the local hardware store.
Can you use 1/2 inch drywall ceiling?
1/2-inch: Half-inch drywall panels are the standard thickness for interior walls, as well as ceilings. 5/8-inch: These panels are commonly used for ceilings, or for walls that require a prescribed fire-resistant rating.
What can I use instead of drywall on ceiling?
If you are planning on redoing your walls or ceilings, the typical materials you’ll use include Sheetrock or finished plywood. Each has its benefits as a building material and in some cases, finished plywood is the better alternative.
How much drywall do I need for ceiling?
For two walls: 270 square feet. Measure the ceiling: 15 x 10 = 150 square feet. Add the areas together: 180 + 270 + 150 = 600 total square feet. Round up: 16.67 = 17 sheets….How to Estimate Drywall or Sheetrock.Sheet SizeSquare Feet4×16644 more rows
Should I nail or screw drywall?
When working with 1/2-inch drywall panels, use 1-1/4 or 1-3/8-inch nails or screws. When working with 5/8-inch drywall panels, use 1-3/8-inch or 1-5/8-inch screws. … In most cases, securing drywall will require fewer screws than nails. Double-nailing panels will help minimize the occurrence of nail pops.
Why do screws pop in drywall?
Screws typically pop out of drywall for one of two reasons: they were installed too deep, or the studs have expanded and contracted. If you drive a screw too deep through the drywall and into the stud, it may pop out. … In a dry environment, studs will release moisture, causing them to contract.
How much weight can a screw in drywall hold?
10 poundsA regular nail or screw in drywall is only going to hold up to 10 pounds. Drywall can flake and break apart, which is why it is recommended to hang items using an anchor. Hollow or drywall anchors are the best way to make sure your wall and object do not get damaged if you are hanging something without a stud.
What is better sheetrock or drywall?
Whether you call it drywall, sheetrock, wallboard, plasterboard, or gypsum board they all are really the same thing – construction materials used to make interior walls and ceilings. … Sheetrock is a safer buy than a non-brand name drywall because sheetrock does not emit sulfur gas.
Do you hang drywall top to bottom?
When hanging the drywall on the walls, always hang the top sheet first. Raise a sheet tight to the ceiling and secure it with a drywall nail at the top and bottom at each stud. Complete the top row throughout the room before proceeding to the bottom.
Does drywall go on the ceiling?
Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. level. Irregularities less than 1/8 in.
Should drywall touch the floor?
Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods.
How big of a gap can you fill with drywall mud?
Another situation that calls for filling is a drywall gap between sheets that’s more than about 1/2 inch wide. If you tape over a wide gap like this without filling it first, the tape will flex, and the joint compound covering it will chip away.
Can you put too many screws in drywall?
Drywall Screw Spacing for the Wall Field Both the International Residential Code (IRC) and USG, the manufacturer of Sheetrock, note that the recommended maximum field screw spacing for wall drywall is 16 inches. Some builders like to space fasteners tighter than that, so they go down to 12 inches.